Sawing Your Own Firewood With A Chainsaw
Protective clothing from head to toe
First things first – When sawing firewood you need to ensure you start with the right equipment. Personal Protective Equipment should be top of that list. Whenever you are working with a chainsaw you should wear face protection and safety glasses to protect your face and eyes from flying wood chips. If you are using a petrol chainsaw, you will also need ear protection, such as ear plugs or ear defenders. For those with more sensitive ears, you can always consider a cordless chainsaw – they are so quiet that they do not require ear protection. Our MSA 120 C-B, MSA 140 C-B and MSA 200 C-BQ have all been awarded a QuietMark, which means they are some of the quietest saws on the market.
You should also protect your hands, legs and feet properly by wearing appropriate cut protective work gloves, chainsaw trousers and boots.
If you don’t use your fireplace often, most wood will be suitable. Soft woods, such as spruce, will heat up faster, due to their higher resin content. This also means that they burn more quickly so you will need to add logs to the fire more often.
Hard woods, such as beech or oak, take longer to heat up but burn for much longer. This makes them well suited if you use your stove or fireplace for longer periods of time.
Make sure the wood is seasoned (dried out) before burning it. For the best burn and heat output, firewood should be seasoned until its moisture content is around 20 percent. Firewood with a higher moisture content is hard to light and keep burning, plus the heat that is produced is wasted in drying the excess moisture. More importantly, the tars and creosote in the smoke produced by the excess moisture can line flue pipes and your chimney and eventually cause a fire. Plus lots of smoke is never a good thing for you or your poor neighbours.
Sawing firewood from a trunk on the ground
So you have a tree trunk or large branch in your garden that can be turned into fuel for your soon-to-be roaring fire? We suggest that you start by cutting the tree, log or branch into much more manageable lengths – one metre lengths work well.
- Lay out the trunks and mark one metre lengths on the bark so that you know where you need to cut. We have marking chalk (which has high pigmentation so you can see your marks) or ECO Marker spray – both are perfect for this job.
- If the trunk is on a fairly firm surface, you can cut the trunk to length where it is. However, before you start sawing, make sure that it cannot roll away. Small pieces of wood can be used to hold it in place.
Sawing the trunk
- Start your chainsaw and position it on the marked points with the chain running slowly. Saw about three-quarters of the way through the trunk at each marked point. This prevents you from cutting into the ground with the chainsaw – cutting into the ground will blunt your chain, which can be dangerous. You can learn to recognise the signs of a dull saw chain with our handy checklist.
- Turn the trunk over, either by hand or with a felling lever. Once again, check that the trunk cannot roll away and wedge it if necessary.
- Saw through the remaining parts of the trunk at each of the marked sections.
You can see these steps in action in our video.
Sawing firewood from a trunk on a support
If the ground is not as stable, a self-made support could be the answer. Cutting a groove in a piece of wood creates an ideal support. Follow these step-by-step instructions.
- To make the support, you will need a small piece of the trunk. Saw a V-shaped groove into it (as in the above picture). The groove should be the same width of the tree trunk you want to cut.
- Make sure the support is stable then place the trunk on it. Hand lifting tongs might be useful here. You do not want the trunk to move.So ensure it is stable and wedge it in place if not.
- Position your saw on the marked points with chain running slowly – this will help to achieve a clean cut. At this point, watch out for where the sawn-off part of the trunk falls – if it falls on your foot, your toes won’t know what’s hit them!
- Keep moving the trunk further up the support and repeat the process until all marked sections have been cut.
Splitting thick tree trunks and one-metre logs
So you will now have several one-metre lengths which will be more manageable. But unless you have a very big fireplace, these lengths now need to be cut into smaller pieces. Smaller logs also dry more quickly and you will definitely want dry logs for your fire. Damp logs will smoke and cause soot – not ideal in your living room!
- Place your one-metre log horizontally and securely on the ground. At the risk of sounding like a broken record, again ensure that it cannot roll away.
- Next, cut the log down the middle along its entire length. Don’t try and cut all the way through the log – this could result in you cutting into the ground and blunting the chain. Leave approximately 5-10 centimetres of the log intact.
- You can then prise the log in two using a splitting wedge. You can cut an indent into the log to fit the wedge into, which will make it easier. It is easiest to use the wedge if an indent for the wedge is first cut into trunk.
- Depending on the thickness of the trunk, you may want to split the log halves again. If so, just follow steps 1 – 3 again.
Making thin trunks, branches and split pieces into firewood
Once your one-metre lengths have been split into thinner lengths (or if your branches were fairly thin in the first place) we suggest that you use a sawhorse. A wooden sawhorse (like the one pictured) is perfect for the job and is a great budget option. Alternatively, our metal sawhorse can support slightly larger trunks and has a spring-loaded chain to secure the log.
Our video shows you how to secure the wood firmly on the sawhorse.
Once you have cut your own logs, they will need to dry for around two years before they can be used on the fire. Make sure that you stack your logs so that the air can circulate between them. Then cover them with a waterproof tarpaulin to protect them from rain and damp weather.
So there you have it – our tops tips for sawing firewood!
THANK YOU FOR VISITING THE STIHL GB BLOG
Here you’ll be able to find useful seasonal advice from experts and guest writers, along with the latest news from the world of STIHL and the great outdoors.
In addition, we’ll keep you informed about our latest products and how to make the most of your tools – all so that you can make the most of your outdoor space.
If you love Christmas, then you’re sure to love indulging in a good festive light display, or getting into the spirit with a visit to Santa. In recent years, many gardens around the country have upped their festive game and... Read more →
RHS Chelsea Flower Show is the place to be and be seen in May if you are a keen gardener. Even if you’re not very green-fingered, there is still plenty to inspire you with perfect plants and gorgeous gardens around... Read more →
For the 14 th year running, STIHL will be sponsoring the ARB Show, and we can’t wait for the annual celebration of the science of trees. It’s the 20 th anniversary of the event and it looks set to be... Read more →
We began working with expert chainsaw carver Simon O’Rourke in 2017 when he joined us at the Arb Show to do a wood carving demonstration. For us, he was an obvious choice for a partnership as he is the best... Read more →